Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Ford AX4N and AX4S problems: Windstar, Sable, Freestar

TSS editorial team · · 15 min read

Transmission specialist inspecting transaxle bearings and gear assemblies on a dark rebuild bench for AX4N and AX4S
In short
  • The AX4S and AX4N are Ford 4-speed front-wheel-drive automatics with a chain drive: the AX4S comes from the AXOD, and the AX4N has been called 4F50N since 2001.
  • In Mexico they're in the Sable with the Duratec engine (AX4N), the Windstar 3.8 (AX4S through 2000 and 4F50N from 2001 to 2003), the Freestar (4F50N) and the front-wheel-drive Lincoln Continental (AX4N).
  • In its US bulletins, Ford has fixes by symptom: reverse clutch seals, a valve body clip, the intermediate piston, a chafed internal harness, a restricted vent and low fluid.
  • With a stuck solenoid it can start in 2nd or 3rd, or not shift into 4th; with the pressure solenoid open or shorted, pressure goes to maximum and shifts are harsh.
  • It takes MERCON V (since 2006, Ford also allows it in 1997 and older units) and never additives; it has a dipstick and the level is checked hot.

The AX4S and AX4N are the 4-speed automatics Ford used from the nineties to 2007 in its front-wheel-drive cars and minivans: the Taurus, Sable, Windstar, Freestar and the Lincoln Continental. The AX4S comes from the 1986 AXOD, and the AX4N has been called 4F50N since 2001. This guide pulls together what Ford's service manuals and bulletins say: which Fords have them in Mexico, their problems by symptom, what the transmission does when a solenoid fails, the codes, test values, the fluid and TSS parts. If you don't know which transmission your Ford has, see which transmission does my Ford have.

What are the AX4S and AX4N?

What they areFord 4-speed electronic overdrive automatics for front-wheel drive (transaxles), with a chain between the converter and the gearsets
AX4SIt comes from the AXOD (1986) and the AXOD-E (1991): Ford says the AX4S "was formerly designated the AXOD". It has an overdrive band and a low-intermediate band
AX4N and 4F50NThe same transmission: Ford called it AX4N through 2000 and 4F50N from 2001. It has an overdrive band, a coast band and a low-intermediate clutch
ComputerThe engine computer (PCM); there's no separate module
SolenoidsThree shift solenoids, a converter solenoid (TCC) and a pressure solenoid (EPC), joined to the case connector by an internal harness
SensorsTurbine speed, output speed, fluid temperature and range; the range sensor is analog on 1990s units and digital on later ones
ID tagOn top of the converter housing
By engineWith the 24-valve 3.0 Duratec, the Taurus SHO's 3.4 V8 and the Continental's 4.6 V8, only the AX4N; the 12-valve 3.0 had both
Door labelOn 2004 and 2005 models, Ford uses L for the AX4S and X for the 4F50N; the letter changes by year
DipstickYes: the level is checked hot, with the engine running
When it endedIn the US, the AX4S in 2003 or 2004, on 12-valve Taurus and Sable models, and the 4F50N in 2007, on the Taurus and the Freestar

Which Fords have them in Mexico?

Sable 1998 to 2003 (3.0 Duratec V6)"Automática con control electrónico de 4 velocidades con sobremarcha": the AX4N, called 4F50N from 2001
Windstar 1998 (3.8 V6)"Automática Electrónica, 4 velocidades y sobremarcha": the AX4S
Windstar 2001 to 2003 (3.8 V6)A 200 hp 3.8 engine; the transmission is the 4F50N (AX4N), per Ford's US documents
Freestar (2004 to 2007)The 4F50N: it's the only transmission Ford lists for the Freestar
Lincoln Continental 1998 (4.6 V8, front-wheel drive)"Automática de control electrónico 4 velocidades con sobremarcha": the AX4N
TaurusWe didn't find it on Ford México's pages from those years; one imported from the US can have either unit
4-speed Contour, Mystique and EscapeNo: they use the CD4E, a different transmission

Ford México doesn't publish the transmission code on these sheets: we infer it from Ford's US documents for the same engine and year. In the US, the Windstar had the AX4S from 1995 to 2000, and 12-valve 3.0 Taurus and Sable models had both units, sometimes in the same year: if yours is an import, check the tag. The AX4N and 4F50N internal harness has its own guide.

AX4N and AX4S problems by symptom

These are the diagnostic routines in Ford's service manuals and what its US bulletins and recalls say:

No reverseThere's no reverse band: reverse uses the forward and reverse clutches and the low one-way clutch. On 1999 units, Ford replaced the reverse clutch lip seals, which tore in extreme cold; on the Windstar and Freestar, check that no water gets into the computer or the vent (more causes)
Goes into neutral when stopping, sometimes with no forward or reverseOn AX4Ns built through February 1998, the seal bonded to the forward clutch piston, which stopped sealing on the 3-2 downshift: Ford replaced the piston, and the plates if they were dark from heat. With code P1700, check the fluid level too
No 4th gear or no overdriveOn AX4Ns through 1998, a broken clip in the valve body, the one that holds the forward clutch control valve (P0734 and P0761). Also shift solenoid 3, the servo and the overdrive band
No 1-2 shift (P0732)On 2004 and 2005 4F50Ns, the intermediate clutch piston seal, which is bonded to the piston, tears or comes loose: Ford replaces the piston and inspects the plates
Harsh 3-2 downshift or shudder when accelerating through a turn (AX4S)Low fluid: air gets into the filter during the turn. Ford fills to the top of the dipstick's crosshatched area, hot
The converter won't lock up (P0741, P1744)Ford checks a list of causes before the converter: stuck valves, the pump shaft and its seals, the turbine shaft seals, a wrong converter solenoid, a damaged internal harness or chain sprockets with a different ratio
The engine stalls when you stop in DThe converter clutch won't release: a stuck or shorted converter solenoid, or its valve
Harsh shifts or engagementsThe pressure solenoid (EPC): open or shorted, the computer goes to maximum pressure. Also the range sensor, the throttle sensor, the speed sensor or the MAF; and after a transmission swap, a unit from another model with a different ratio
Several solenoid codes at onceOn 2005 4F50Ns built before March 15, 2005, the side cover chafed the yellow wire of the internal harness near solenoid C (P0760 and P0763): Ford replaces the harness and the cover. Also wires chafed on top of the pan or blown fuses
Sudden loss of forward and reverse (2004 and 2005 Freestar and Monterey)In the US, recall 12V-006: the converter splines that drive the pump wore out. Ford replaced the converter and says that failure doesn't damage other transmission parts
Overheats (P1783)The fluid went above 149 °C (300 °F): fluid level and condition, restricted, damaged or reversed cooler lines, engine overheating, a converter that won't lock up or heavy towing
Erratic dipstick readings or a leak at the filler tube (2000 to 2007)A restricted vent: Ford fits a new one with a hose, and warns this leak gets mistaken for a pan gasket leak

Stuck in one gear: the shift solenoids

In Ford's 1990s manuals the shift solenoids are called SS1, SS2 and SS3, and in the 2001-on manuals, SSA, SSB and SSC. This is Ford's chart for the AX4N and AX4S with a stuck solenoid, with the lever in D (overdrive on):

Solenoid 1 always offAX4N: 1st, 2nd, 2nd and 1st. AX4S: 1st, 1st, 3rd and 3rd
Solenoid 2 always offAX4N: starts in 2nd (2nd, 2nd, 3rd and 3rd). AX4S: starts in 3rd (3rd, 2nd, 3rd and 4th)
Solenoid 3 always offAX4N: no 4th (1st, 2nd, 3rd and 3rd). AX4S: 1st, 2nd, 3rd and 2nd
Solenoid 1 always onAX4N: starts in 3rd (3rd, 3rd, 3rd and 4th). AX4S: starts in 2nd (2nd, 2nd, 4th and 4th)
Solenoid 2 always onAX4N: 1st, 1st, 4th and 4th. AX4S: 1st, 2nd, 1st and 2nd
Solenoid 3 always onNormal shifts; on the AX4N, no engine braking in 3rd with overdrive cancelled

With all three solenoids off, for example with the connector unplugged, these charts put the AX4N in 2nd and the AX4S in 3rd; Ford doesn't call it limp mode. A solenoid that's "off" can be the solenoid, the wiring or the computer, and Ford warns that ratio codes can also be set by stuck valves or damaged frictions.

AX4N and AX4S trouble codes

P0731, P0732, P0733 and P0734Incorrect ratio in 1st, 2nd, 3rd or 4th. Ford says it can also be stuck valves or damaged frictions, not just the solenoids (guide)
P0750, P0755 and P0760 (on 2005 units, also P0753, P0758 and P0763)Shift solenoid 1, 2 and 3 circuits: open, shorted or a computer fault (guide)
P0751, P0756, P0761, P1751, P1756 and P1761 (on 2005 units, P1714, P1715 and P1716)Mechanical or hydraulic failure of a shift solenoid
P0741, P1741 and P1744The converter slips or won't lock up; with P1741, the car surges or shudders at a steady speed. The computer doesn't set P0741 until the converter fails 5 times in a row
P0743, P1742 and P1743 (on 2005 units, also P1740)Converter solenoid: shorted or stuck, the engine stalls when you stop in D; open, it never locks up
P1746, P1747 and P1760 (on 2005 units, P1747, P0960, P0962 and P0963)Pressure solenoid (EPC) circuit: open or shorted, the computer goes to maximum pressure, with harsh engagements and shifts
P1700Low one-way clutch failure: no 1st, 2nd or reverse, together with P0731 and P0732. Ford says low fluid can set it too
P0705, P0707 and P0708Range sensor: high pressure and harsh shifts. On 1997 units, with P0707 it stays in 3rd and with P0708 there's no overdrive; with the digital sensor, the transmission behaves as in D in every position (guide)
P0715, P0717, P0720 and P0722Turbine and output speed sensors: wrong converter lockup and harsh shifts (guide)
P0500 and P1500Vehicle speed sensor on 1990s units: harsh shifts and no converter lockup. Ford says P0500 can also be set by low fluid
P0712 and P0713Fluid temperature sensor (guide)
P1783The fluid went above 149 °C (300 °F): the computer raises pressure
P1780The overdrive button doesn't change state

The O/D OFF light comes on when you cancel overdrive and flashes when the computer detects a sensor or solenoid fault (what each light means). Before opening the transmission, Ford fixes engine codes first (MAF, temperature, throttle, misfires): they can cause harsh or soft shifts or keep the converter from locking up. You can look up other codes in our diagnosis by code.

Test values

Shift solenoids15 to 25 Ω
Pressure solenoid (EPC)3.23 to 5.50 Ω
Converter solenoid0.98 to 1.6 Ω on 1992 to 1997 Taurus and Sable models, Windstars built through September 8, 1997 and 1991 to 1996 Continentals; 13 to 24 Ω after that
Turbine speed sensor100 to 200 Ω
Line pressure at idle, in P, N and DAX4N: 414 to 579 kPa (60 to 84 psi). AX4S: 331 to 531 kPa (48 to 77 psi)
Line pressure at idle, in RAX4N: 538 to 745 kPa (78 to 108 psi). AX4S: 421 to 683 kPa (61 to 99 psi)
Line pressure at wide-open throttle, in DAX4N: 1,434 to 1,772 kPa (208 to 257 psi). AX4S: 1,220 to 1,393 kPa (177 to 202 psi)
EPC pressure69 to 138 kPa (10 to 20 psi) at idle; 483 to 620 kPa (70 to 90 psi) at wide-open throttle
Stall speed1,860 to 2,200 rpm with the 12-valve 3.0; 1,940 to 2,300 with the Duratec; 2,316 to 2,714 with the 2001 Windstar's 3.8

These are values from Ford's service manuals for the 1997 Taurus (AX4S and AX4N) and the 2001 Windstar, and from its bulletin 03-12-3 for the converter solenoid. Ford runs the pressure test first, and if pressure is low at stall it skips the stall test to avoid more damage; never more than 5 seconds at full throttle. If line pressure is wrong and there are no codes, Ford checks EPC pressure: if that's wrong too, it replaces the EPC solenoid.

Which fluid does it take, and how is it checked?

Through 1997 they took MERCON, and from 1998, MERCON V (on the 1998 Windstar, from units built on September 9, 1997). In 1998 Ford said not to use MERCON V in 1997 and older units, but its 2006 bulletin 06-14-4 changed that: units that took MERCON are now serviced with MERCON V or dual MERCON/MERCON V fluid. Don't use additives or cleaners: Ford prohibits them.

The AX4S holds about 11.6 liters in total, and the AX4N 12.7 to 13.0 liters depending on the vehicle. Dropping the pan only drains part of it: in an AX4S program, Ford refilled about 2.8 liters (3 quarts) and topped off by the dipstick with the transmission hot.

It has a dipstick. Ford checks the level with the fluid at operating temperature (66 to 77 °C, 150 to 170 °F, after about 30 km or 20 miles), on level ground, with the engine running, after moving the lever through every position and back to P; the level should be in the crosshatched area. Too much fluid causes shift problems too, and on the AX4S, low fluid lets air into the filter in turns. Normal fluid is dark red; brown, black or a burnt smell means damage, and pink foam means coolant in the transmission.

After any repair, Ford flushes the cooler and its lines: it says cooler contamination is the number one cause of a repaired transmission failing again. More in our cooler and fluid leak guides.

AX4N and AX4S myths

  • "The AX4N and the 4F50N are different transmissions." They're the same unit: Ford called it 4F50N from 2001. Even so, several parts change by year.
  • "The Windstar always had the AX4N" or "the Freestar has the AX4S". According to Ford, the Windstar had the AX4S through 2000 and the 4F50N from 2001 to 2003, and the Freestar only the 4F50N.
  • "Never put MERCON V in a 1997 or older unit." That was the 1998 rule; since 2006, Ford services them with MERCON V.
  • "A harsh 3-2 or a shudder in turns means the transmission is finished." On the AX4S, Ford blames low fluid: check the level first.
  • "With P0741 or P1744, replace the converter." Ford checks a list of causes first and says not to replace good converters.
  • "Several solenoid codes: replace all the solenoids." Ford found chafed harnesses and blown fuses: check the wiring first.
  • "No reverse means the reverse band." There's no reverse band: reverse uses the forward and reverse clutches and the low one-way clutch.
  • "Any used transmission will fit." Ford warns the ratio changes by model and year: the wrong unit gives harsh shifts and P0741 or P1744.
  • "A leak at the filler tube is the pan gasket." Ford found the cause is a restricted vent, and that it gets mistaken for the gasket.
  • "Disconnecting the battery fixes the transmission." It only erases what it learned: the transmission relearns its shifts and may shift harshly at first.
  • "Additives fix slipping." Ford prohibits them, and warns solvents damage the friction bonding.

How is it diagnosed?

  • Check the fluid level and condition hot, with the engine running.
  • Read the codes with a scan tool: Ford fixes engine codes first and transmission codes second.
  • If the O/D OFF light flashes, pull the code before replacing parts.
  • Check connectors and harnesses: the transmission's, the range sensor's and the speed sensors'; on the Windstar and Freestar, that no water gets into the computer.
  • Measure the solenoids and sensors against Ford's values.
  • Run the line pressure test, then the stall test.
  • Only then open the transmission: the valve body, the internal harness, the clutches and the bands; the converter comes last.

If you swap the transmission, use the tag to confirm it's the one for your model and year: the ratio changes, and the wrong one gives harsh shifts and converter codes. After a battery disconnect, the transmission relearns its shifts.

See AX4N and AX4S parts

TSS parts for the AX4N and AX4S

The AX4S, AX4N and 4F50N page has every TSS part for these units. These are the ones that match the jobs in this guide:

Fluid and filter changeGreen-seal filter (AX4S from 1996 and AX4N from 1997) or orange-seal filter (earlier years); AX4N or AX4S pan gasket
SolenoidsShift solenoid (the same for all three positions), converter solenoid and AX4S or AX4N EPC solenoid
Range sensor8-pin, 1993 to 1997 or 10-pin digital, 1998 on
Speed sensorAX4N digital, 1995 to 1999, AX4S magnetic or 1986 to 1999
LeaksGaskets for the AX4N side cover (1995 to 2000) and the chain cover: 1986 to 1999, AX4S 2000 on, AX4N 2000 to 2003 and 2004 on; converter seal
No 4th or no overdriveOverdrive band, the same for both units
Other bandsThe AX4N coast band, for engine braking in manual 2 and 1, and the low-intermediate band from the AXOD to the 1994 AX4S, for 1st and 2nd
Slipping or no reverseForward and reverse friction plates
No 1-2 shift (P0732)Bonded intermediate clutch piston
Soft or slipping shifts (4F50N, 2004 on)2-3 capacity modulator valve spring
Transmission overhaulDorado gasket kit, AX4N 1994 to 1999, valve body gasket kit, pump bushing and AX4S bushing kit

Choose the filter, the range sensor and the chain cover gasket by year: Ford changed the park system in 1999 and 2000, and the chain cover and its gasket don't interchange with the earlier ones. Ford used converter solenoids with different resistance by year, and the wrong one causes P0741 or P1744: measure yours and confirm with Veinte 07 before ordering, as with the intermediate piston's year. Compare the range sensor's connector with your transmission's too. TSS internal harnesses, turbine speed sensors, chains and converters for these units are out of stock for now. If you're torn between gasket kits, read how they differ.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What's the difference between the AX4N and the 4F50N?

    They're the same transmission: Ford called it AX4N through 2000 and 4F50N from 2001. Some parts change by year, so order by year and by the transmission tag.

  • What's the difference between the AX4S and the AX4N?

    Both are Ford 4-speed chain-drive automatics, but inside they're different: the AX4S has a low-intermediate band, and the AX4N has a coast band and a low-intermediate clutch. Many parts don't interchange.

  • Which transmission does the Windstar have?

    According to Ford's US documents, the AX4S from 1995 to 2000 and the 4F50N (AX4N) from 2001 to 2003. The Mexican 1998 spec sheet says "automática electrónica, 4 velocidades y sobremarcha".

  • Which transmission does the Freestar have?

    The 4F50N, which is the AX4N under another name. It's the only transmission Ford lists for the Freestar and the Mercury Monterey.

  • Which fluid does the AX4N take?

    MERCON V. Units from 1997 and earlier took MERCON, and since 2006 Ford services them with MERCON V too. Don't use additives.

  • How many liters does the AX4N hold?

    12.7 to 13.0 liters in total, depending on the vehicle; the AX4S, about 11.6. Dropping the pan only drains part of it: top off by the dipstick with the fluid hot.

  • Why does my Windstar have no reverse?

    Check the fluid level and the codes first. Ford found reverse clutch seals torn by extreme cold on 1999 units, and water in the computer or the vent on 1999 to 2003 Windstars and on Freestars.

  • Is there a campaign for the Freestar's transmission?

    In the US, Ford replaced the converter on 2004 and 2005 Freestar and Monterey vans in recall 12V-006, because the splines that drive the pump wore out. We don't know whether it applied in Mexico.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.