
- The E4OD and 4R100 are the same Ford 4-speed automatic for heavier trucks and vans: Ford renamed it 4R100 around 1998 and used it through 2004 in the US.
- In Mexico it's in the Club Wagon and Econoline E-350 with the 5.4 V8 or the 7.3 diesel, the Expedition 5.4 and the Excursion V10; the 1997 to 2003 Mexican F-250 used the 4R70W.
- A flashing O/D light is the transmission light: it warns of a pressure circuit fault, a sensor fault or slipping. Ford says not to replace the converter without proof.
- With a stuck shift solenoid it can start in 2nd or 4th, or not shift into 4th; with the lever in 2 it always gives 2nd.
- It takes MERCON V or MERCON/MERCON V since 2006, never MERCON SP or additives, and has a dipstick: check the level hot with the engine running.
The E4OD and 4R100 are the 4-speed automatic Ford put in its heavier trucks and vans from 1989 to 2004: the F-250 and F-350, Super Duty, Econoline, Expedition and Excursion. Ford renamed it 4R100 around 1998, but it's the same family. This guide pulls together what Ford's service manual and bulletins say: which Fords have it in Mexico, what the codes mean, what happens when a solenoid fails, test values, the fluid and TSS parts. If you don't know which transmission your Ford has, see which transmission does my Ford have.
What are the E4OD and 4R100?
| What to check | E4OD and 4R100 |
|---|---|
| What it is | A Ford 4-speed electronic overdrive automatic, rear-wheel drive, for heavier trucks and vans |
| E4OD or 4R100 | Same family: Ford called it E4OD from 1989 to 1998 and 4R100 from 1998 or 1999, depending on the model |
| Engines | 4.9 six; 5.0, 5.8, 7.5 and 5.4 V8s; 6.8 V10; and 7.3 diesel |
| Computer | The engine computer (PCM); on some 1990s E4OD diesels, a separate transmission module |
| Solenoids | Two shift solenoids, a converter solenoid, a coast clutch solenoid and a pressure solenoid (EPC), together in a solenoid body that isn't serviced piece by piece |
| Range sensor | Analog on the E4OD, digital on the 4R100 |
| ID tag | On the left side of the case, behind the range sensor |
| Dipstick | Yes: the level is checked hot, with the engine running in P |
| Power take-off | The 4R100 could have it as an option with the 6.8 and 7.3 diesel engines |
| When it ended | In the US, in 2004 on gas E-Series and Super Duty trucks; it was replaced by the 5R110W TorqShift and, on light E-Series vans, the 4R75E |
Which Fords have it in Mexico?
| Vehicle in Mexico | What Ford México says |
|---|---|
| Club Wagon 5.4 V8 (1998) | "Motor 5.4L EFI/Trans. Automática 4-vel. Elect.": the E4OD |
| Econoline Wagon E-350 5.4 (2002) and E-350 Wagon 7.3 diesel (2003) | "Automática electrónica de 4 velocidades con sobremarcha (estándar en E-350 Wagon)": the 4R100 |
| Expedition 5.4 (1997 to 2002) | Electronic 4-speed automatic: the E4OD through 1998 and the 4R100 after that (with the 4.6, the 4R70W) |
| Excursion 6.8 V10 (2001 to 2003) | "Transmisión Aut 4 vels": the 4R100 |
| 2002 Lobo Harley-Davidson (supercharged 5.4) | "Automática de 4 velocidades con sobremarcha de uso pesado": probably the 4R100 |
| F-250, 1997 to 2003 | No: in Mexico it was the F-150-based truck, with the 4R70W (the 2002 spec sheet names it) |
| 2002 Super Duty chassis cab | No: Ford México's spec sheet lists only manual transmissions |
| F-250 and F-350 Super Duty imported from the US (1999 to 2004) | Yes: with gas or the 7.3 diesel, the 4R100 |
| Econoline E-150 4.2 V6 | No: the 4R70W |
Ford México doesn't publish the transmission code on these sheets, except the 2002 F-250's, which names the 4R70W: we infer it from Ford's US documents for the same engine and year. If your truck is an import, check the transmission tag. The 4R70W, used by that era's Mexican F-250, and the 5R110W, used by the 2003-on 6.0 diesel Super Duty, have their own guides.
E4OD and 4R100 problems by symptom
These are the symptom routines in Ford's service manuals and what its US bulletins say:
| Symptom | What Ford checks |
|---|---|
| The O/D light (the overdrive cancel light) flashes | Ford uses it as the transmission light: a pressure circuit (EPC) fault, a sensor fault or slipping. Read the code before blaming the converter |
| Harsh or very soft shifts | The pressure solenoid (EPC), the range sensor and engine sensors (MAF, throttle); on the 7.3 diesel, if the pedal sensor fails, the computer raises line pressure |
| Starts in 2nd or 4th, skips shifts or won't shift into 4th | A stuck shift solenoid (below), stuck valves or damaged frictions; on 2001 builds, the intermediate one-way clutch |
| Slips, or the engine flares between shifts | Any clutch or the converter, low line pressure, leaks or sticking valves |
| The engine stalls when shifting into gear or coming to a stop | A shorted converter solenoid; on 1996 to 1998 E4ODs, a loose or dropped pan filter |
| Converter shudder | The converter solenoid, the lockup regulator valve, the Teflon seal on the stator support, pump leaks and converter end play |
| Overheats (P1783) | Load, towing or power take-off, a restricted cooler or bypass valve, or a converter that won't lock up |
| No engine braking in 2nd | The intermediate band and its servo |
| Leaks | The pan gasket (cork or rubber, which aren't interchangeable), the pump seal and the shift lever seal |
Stuck in one gear: the shift solenoids
This is Ford's chart for the 4R100 with a stuck shift solenoid:
| Fault | What the transmission does |
|---|---|
| Solenoid A always off | In D it starts in 4th: 4th, 3rd, 3rd and 4th |
| Solenoid B always off | In D only 1st and 4th, no 2nd or 3rd |
| Solenoid A always on | In D only 1st and 2nd, no 3rd or 4th |
| Solenoid B always on | In D it starts in 2nd and reaches 3rd, no 4th |
| Either one | With the lever in 2, it always gives 2nd |
With both solenoids off, the transmission sits in its 4th-gear state in D, and with the lever in 2 you have 2nd to keep moving. Ford warns that shift codes can also be set by stuck valves or damaged frictions, not just the solenoid.
E4OD and 4R100 trouble codes
| Code | What it means, according to Ford |
|---|---|
| P0781, P0782 and P0783 | 1-2, 2-3 or 3-4 shift error: no rpm drop when the computer commands the shift. Ford says it can also be stuck valves or damaged frictions (guide) |
| P0750 and P0755 (P0753 and P0758) | Shift solenoid circuits (guide) |
| P0751, P0756, P1714 and P1715 | Mechanical or hydraulic failure of a shift solenoid |
| P0743 and P0740 | Converter solenoid circuit: shorted, the engine stalls in D or 2 when you stop; open, it never locks up |
| P1728, P0741 and P1744 | Slipping in the transmission or the converter; Ford says not to replace the converter without proof |
| P1747 and P1746 | Pressure solenoid (EPC) circuit: shorted gives minimum pressure and limits the engine, which seems to misfire; open gives maximum pressure and harsh shifts |
| P1754 | Coast clutch solenoid: no 3rd-gear engine braking with overdrive cancelled, or 3rd-gear engine braking without cancelling it |
| P0705, P0707 and P0708 | Range sensor; on the 4R100, with P0705 pressure rises and the transmission behaves as in D in every position (guide) |
| P0715 to P0722 | 4R100 turbine and output speed sensors: harsh or erratic shifts (guide) |
| P0712 and P0713 | Fluid temperature sensor (guide) |
| P1783 | The fluid went above 132 °C (270 °F) |
| P1780 | The overdrive button doesn't change state |
Before opening the transmission, Ford fixes engine and sensor codes first (MAF, throttle, barometric pressure and, on the diesel, injection control pressure): they can cause harsh shifts, late shifts at altitude or a flashing O/D light. You can look up other codes in our diagnosis by code.
Test values
| What to measure | Value according to Ford |
|---|---|
| Shift, converter and coast solenoids (E4OD) | 20 to 30 Ω |
| EPC pressure solenoid (E4OD) | 4.0 to 6.5 Ω |
| Line pressure at idle, P and N | 50 to 65 psi (345 to 448 kPa) |
| Line pressure in R | 70 to 100 psi at idle; 245 to 290 psi at stall |
| Line pressure in D and 2 | 50 to 65 psi at idle; 165 to 185 psi at stall |
| Stall speed | About 1,600 to 2,700 rpm depending on the engine; for example, 2,049 to 2,381 on the 2001 Super Duty 7.3 diesel |
| Cooler flow | About 946 ml (32 oz) in 15 seconds, at idle in N |
These are values from Ford's service manuals for the 1996 F-250 (E4OD) and the 2001 Super Duty (4R100); each engine has its own stall speed. Ford runs the pressure test first, and if pressure is low at stall it skips the stall test to avoid more damage; never more than 5 seconds at full throttle, and 15 seconds in N between positions.
Which fluid does it take, and how is it checked?
Originally, MERCON. Since its 2006 bulletin 06-14-4, Ford services these units with MERCON V or dual MERCON/MERCON V fluid, because MERCON went out of production. Don't use MERCON SP, which is the TorqShift's fluid, or additives: Ford prohibits them. It holds about 15 to 16.7 liters in total, depending on the model and the cooler.
It has a dipstick. Ford checks the level with the fluid at operating temperature, on level ground, with the engine idling in P and the parking brake on, after moving the lever through every position; on the E4OD, at 66 to 77 °C (150 to 170 °F). If it's below the DO NOT DRIVE mark, don't drive. With too much fluid it foams and vents; with too little the transmission slips. Normal fluid is dark red, not brown or black and without a burnt smell, and pink foam means coolant from the radiator.
For severe use (towing, lots of idling, heavy loads), Ford changes the fluid and filter about every 34,000 to 35,000 km (21,000 miles). Both have a converter drain plug, and 2WD and 4WD filters and pans aren't interchangeable. After any repair, Ford flushes the cooler, its lines and its bypass valve, and fits an in-line filter on the return line, changed every 48,000 km (30,000 miles). More in our cooler and fluid leak guides.
E4OD and 4R100 myths
- "A flashing O/D light means the converter." Ford says those codes are set by slipping anywhere in the transmission, and says not to replace the converter without proof.
- "With the light flashing, the computer goes to maximum pressure." It depends: a shorted EPC gives minimum pressure and limits the engine; an open one, maximum pressure.
- "Solenoid code: replace the solenoid body." Ford says it can also be stuck valves or damaged frictions; on 2001 builds, P0781 with P0755 and P0756 was the intermediate one-way clutch.
- "Any ATF will do." Ford calls for MERCON V or MERCON/MERCON V; not MERCON SP and no additives.
- "It's sealed for life." It has a dipstick, and Ford gives fluid and filter changes for severe use.
- "Additives fix slipping." Ford prohibits them, and warns solvents damage the friction bonding.
- "The 4R100 is a different transmission." It's the same family as the E4OD, with a digital range sensor, speed sensors and optional power take-off; many parts change by year.
- "The 1997 to 2003 Mexican F-250 has the 4R100." That F-250 is the F-150-based truck, with the 4R70W.
- "You can mix valve body parts from any year." Ford warns that mixing separator plates and gaskets from different years causes shift problems or damage.
How is it diagnosed?
- Check the fluid level and condition hot, with the engine running in P.
- Read the codes with a scan tool and fix engine and sensor codes first.
- If the O/D light flashes, pull the code before blaming the converter.
- Check connectors and harnesses: the transmission's, the range sensor's and the speed sensors', with no corrosion and no splices for accessories like trailer brake controllers or radios.
- Measure the solenoids and the temperature sensor, and the digital range sensor voltages.
- Run the line pressure test, then the stall test and the cooler flow test.
- Only then check the valve body and solenoid body, the clutches and the band; the converter comes last.
After any repair, use the right filter and pan for 2WD or 4WD and don't mix valve body plates or gaskets from other years. On gas engines, if you disconnected the battery, the transmission relearns its shifts within a few hundred kilometers.
TSS parts for the E4OD and 4R100
The E4OD and 4R100 page has every TSS part for these units. These are the ones that match the jobs in this guide:
| Problem or job | TSS part |
|---|---|
| Fluid and filter change | 2WD and 4WD filters, and bonded pan gasket |
| E4OD range sensor (1989 to 1996) | 8-pin analog TR switch |
| 4R100 speed sensors | Without power take-off and with power take-off |
| Valve body (4R100, 1998 on) | Rebuilt valve body |
| Transmission overhaul | H-D gasket kit and bushing kit |
| Slipping | Direct, forward and reverse friction plates |
| No engine braking in 2nd | Intermediate band |
Choose the filter and gasket for your unit: 2WD or 4WD, and a pan with a cork or a rubber gasket. TSS's TR switch is the E4OD's analog one and doesn't fit the 4R100's digital sensor, and the speed sensors differ if the transmission has power take-off. TSS solenoid bodies and converters for this unit are out of stock for now. If you're torn between gasket kits, read how they differ.
TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.
Filtro 2wd Plastico y Metal E4OD 4R100
Filtro Plastico / Metal 4x4 1989/up E4od 4r100
Empaque de Carter Vulcanizado E4OD 4R100 5R110W
SWITCH TR MLPS ANALOGO 8 PINES KIT DE ACTUALIZACION 1989/96 E4OD
Sensor Velocidad Modelos No PTO 1998/UP 4R100
Cuerpo de Válvulas Reconstruido 4R100 1998-UP Ford
Juego de Empaques TSS H-D E4OD 4R100
Banda Flexible Intermedia E4OD 4R100



